How to Seal and Stain Pressure Treated Wood Decking

Most decks are made from pressure treated pine. Here is how to keep your deck looking great and protected.

Steps

  1. Image titled Seal and Stain Pressure Treated Wood Decking Step 1
    1
    Remove staining, mildew and old finish with a commercial deck cleaning solution. Pressure washing is almost always a must on older decks, but be sure not to use too much pressure. You can damage the wood if it's turned up too high. Usually 1500-2500 PSI is adequate for pressure treated lumber. Stay between 1200-1500 PSI for cedar and redwood.[1]
  2. Image titled Seal and Stain Pressure Treated Wood Decking Step 2
    2
    After cleaning the wood, let surface dry very well. Most coatings require that the wood should be dry before application. There are exceptions. Thompson's Water Seal Advanced Wood Protectors can be applied to damp lumber, so it's possible to clean and waterproof your deck in one day. Read the directions on the product you're using for temperature and weather guidelines, drying times, etc., and follow them![2]
    Advertisement
  3. Image titled Seal and Stain Pressure Treated Wood Decking Step 3
    3
    Choose your finish. You can use an oil base or water base sealer or stain, solid or semi-transparent. The best method for applying the material is with a brush or a paint pad on a long handle, available at any hardware store. Most materials can be sprayed also, but you will end up needing a lot more product this way. For a large deck, spraying will save time but you should brush the material into the wood. This will help with uniformity and provide a better looking job.[3]
  4. Image titled Seal and Stain Pressure Treated Wood Decking Intro
    4
    Finished.
    5. Advertisement

Community Q&A

  • Question
    Can I use boiled linseed oil on treated deck wood before applying Thompson's Water Sealer?
    Community Answer
    Community Answer
    Read the Thompson's MSDS, it is boiled linseed oil and some solvents. The operative chemical in Thompson's is linseed oil. For generations farmers used linseed oil to protect wood and metal. Thin linseed oil with paint thinner and apply it like Thompson's.
  • Question
    When can I stain a new pressure treated deck?
    Community Answer
    Community Answer
    If you treated it during the summer, wait two to three months. If you treated it in the fall, wait until spring.
  • Question
    How do I handle a peeling, painted deck that has treated lumber?
    Community Answer
    Community Answer
    Use a pressure washer to remove the paint. (Avoid focusing pressure in any one spot or you might end up ripping away some of your deck surface.) Follow with an opaque penetrating deck sealer to hide any remaining color you might have.
Advertisement

Warnings

  • Be careful when using a sprayer and sealant on decks. The over spray may kill nearby grass and shrubs. To prevent this cover the adjacent greenery with a tarp or newspapers.
    ⧼thumbs_response⧽
  • FIRE HAZARD: Before disposing of rags, spread them out to dry completely. Heat generated from evaporating finish on a pile of rags can start a flash fire. If you are using latex stain, clean equipment with soapy water. If you are using oil-based sealers, clean with paint thinner or mineral spirits..
    ⧼thumbs_response⧽
  • Do not use varnish!
    ⧼thumbs_response⧽
  • The sealant may drip between the decking boards, so use tarps beneath the deck to avoid staining a cement pad.
    ⧼thumbs_response⧽
  • Treated lumber does not hold paint well, so avoid painting.
    ⧼thumbs_response⧽
  • A clear finish usually needs to be treated more often.
    ⧼thumbs_response⧽
  • If the deck is near a chlorinated swimming pool, check your selection of stains and oils because the chlorine vapors can cause some oils to become opaque.
    ⧼thumbs_response⧽
  • A deck that does not get a lot of sunlight is more likely to have mildew staining and green moss. This is a black staining or green fungus. Try to avoid oil-based products if the deck doesn't get a good amount of sunlight.
    ⧼thumbs_response⧽
  • Pressure-treated wood may contain arsenic, so EXTREME caution should be used when sanding it. Arsenic is known to cause cancer in adults and children.
    ⧼thumbs_response⧽
  • Use a light-colored stain if your deck gets a lot of sunlight. A dark stain will make the wood get hotter.
    ⧼thumbs_response⧽
Advertisement

You Might Also Like

How to
Weather Wood
Get Water Stains Off Wood
How to
Get Water Stains Off Wood
Install Deck Piers
How to
Install Deck Piers
Refinish Wood Floors
How to
Refinish Wood Floors
Remove Mold Stains from Wood Floors
How to
Remove Mold Stains from Wood Floors
Build a Deck Railing
How to
Build a Deck Railing
Build Deck Stairs
How to
Build Deck Stairs
Build a Deck Around an Above Ground Pool
How to
Build a Deck Around an Above Ground Pool
Repair Trex Decking
How to
Repair Trex Decking
Clean Deck Wood
How to
Clean Deck Wood
Paint a Deck
How to
Paint a Deck
Build a Deck Cover
How to
Build a Deck Cover
Clean a Deck with Bleach
How to
Clean a Deck with Bleach
How to
Build a Deck
Advertisement

References

  1. ↑ https://www.thisoldhouse.com/how-to/go-old-deck-to-new-4-steps
  2. ↑ https://www.familyhandyman.com/decks/how-to-revive-a-deck/
  3. ↑ https://www.familyhandyman.com/decks/choosing-the-best-finish-for-your-deck/
  4. https://www.todayshomeowner.com/video/protecting-a-wood-deck-with-stain/
  5. https://www.bobvila.com/articles/homemade-deck-cleaner/
  6. https://www.todayshomeowner.com/video/how-to-clean-and-finish-a-wood-deck/
  7. Lowes instructions for cleaning and sealing your deck

About This Article

wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 24 people, some anonymous, worked to edit and improve it over time. This article has been viewed 760,658 times.
206 votes - 90%
Co-authors: 24
Updated: September 15, 2021
Views: 760,658
Categories: Decks
Advertisement